Factory says the goods are ready: inspect before final payment

Author: Marad Abdullayev, China business expert · 18.11.2026 · 5 min read

MYRON TRADE editorial illustration, not a client project photograph

Your Chinese factory sends a message: “The order is ready, please transfer the remaining balance.” A photo of sealed cartons does not establish that the quantity is right, the equipment works or the goods match the approved sample. A pre-shipment quality inspection before final payment gives the buyer evidence while the goods are still in China and corrections may still be practicable.

“Ready” does not necessarily mean “accepted”

A completed-looking batch may have untested products, missing accessories or packaging that does not meet the transport brief. Before booking an inspector, decide which measurable criteria will count as acceptance. “Good quality” is not a test method; an agreed specification, approved sample and test list are much more useful.

Factory claim Inspector's task Risk if assumed
“Production is complete” Count and identify the batch Short shipment or mixed products
“Everything works” Perform agreed functional tests Equipment failure after arrival
“Quality is fine” Compare with specification and sample Dispute over subjective criteria
“Goods are packed” Check marking, protection and cartons Damage and mislabelling
“Balance is due” Report findings for buyer decision Reduced leverage to correct problems

A real MYRON TRADE inspection: 350 sauna heaters

One customer ordered approximately 350 electric sauna heaters. The original plan was to test only 50 units. Among the first ten inspected, four failed: some did not heat, some shut down during operation, some had sensor configuration faults, and one unit suffered burnt wiring when powered on.

After receiving the photographs, video and test findings, the customer expanded the scope to the entire batch. Two more inspectors joined the first one. Three people worked for about three eight-hour days, connecting units, observing them over time and opening housings where the agreed method required it. This was a functional inspection, not a superficial carton count.

The factory acknowledged the defects and took approximately 10–14 days to implement corrections. MYRON TRADE then retested about 350 units; the identified faults had been remedied. The team also helped negotiate a discount and reimbursement of inspection expenses by the supplier. These are the reported outcomes of one actual project, not promises applicable to every order.

Diagram 1: verified inputs and sequence
A visual guide to preparing and checking the assignment.

How much of a batch should you inspect?

Sample inspection may be appropriate for a homogeneous lot when the test method and acceptable risk are agreed. If early tests show a concentration of defects, the buyer may choose to enlarge the sample or arrange inspection of every unit for the testable characteristics. “100% inspection” cannot imply that all possible hidden defects have been ruled out: some methods are destructive, require specialised equipment or depend on later operating conditions.

Situation Possible approach Key limitation
Standardised low-risk goods Agreed sample-based inspection Some defects may remain undetected
Several failures in the first sample Expand the check and pause payment decision Extra time and expense
High-value industrial machinery Pre-agreed FAT or technical tests May need an engineer and test equipment
Supplier has corrected faults Repeat affected tests and relevant checks Access and methodology still matter
Goods already sealed Agree on opening and repacking Some characteristics may be inaccessible
Diagram 2: practical steps and checks
Figures and stages are subject to the qualifications in the article.

Give the inspector a usable specification

A factory inspector cannot guess what the buyer considers acceptable. Electric goods need a safe power supply and a test sequence; mechanical products require tolerances and measurement points; textiles need dimensions and defect definitions. Provide an approved reference sample, drawings, critical defect examples, quantity and packing requirements wherever available.

Report section Evidence worth requesting
Lot identification Order reference, serials and packaging photos
Quantity Agreed count or sampling basis
Appearance Overall views and close-ups of defects
Function Test conditions, measurements and video
Supplier response List of issues acknowledged and correction plan
Open questions What still needs a decision before shipping

An inspector reports observations; the customer decides whether to pay, rework or delay dispatch. Inspection does not replace mandatory certification or guarantee future operation free of hidden faults.

Cost and arranging an urgent visit

MYRON TRADE's indicative price for a normal quality visit is USD 330–350, plus travel or specialised test costs when applicable. In a major city or nearby industrial area, a visit can often be arranged within 24 hours if a suitable inspector is free and the plant permits access. Contact the team before committing to a final-payment date.

If the concern is not the batch but whether the supplier is a legitimate factory, that is a separate supplier verification service.

Request a pre-payment inspection on WhatsApp. Include the goods, quantity, factory city, specifications, tests and date the balance is due. Service details: quality control in China.

Need help with this topic?

Describe the task in your own words — even if you are not sure which service you need. A manager will clarify the details and suggest how to proceed and what it will cost.

What happens next

  1. A manager clarifies the detailsin the channel you choose
  2. We propose a work plan and a quotewith an estimate of cost and timing
  3. We agree the terms and startcontract with our company in Shanghai

Or message us directly

New request

Where should we reply

Discuss your taskWhatsApp